变频器制作-第九部分之ESP32C3 也能输出svpwm

前言 先看以下乐馨官方的 ESP32S3 和 ESP32C3 的对比 很明显,ESP32C3 缺乏 MCPWM 设备。 所谓 MCPWM, 就是专门为产生svpwm设计的电路。他能产生6路互补的PWM信号,并且实现中央对齐。然后还能实现在PWM信号的特定位置产生同步事件。app据此可以在这个同步事件上实现电流采样。 一度我以为 ESP32C3 是无法用于驱动电机的。 直到一次偶然,我看到 SimpleFOC 的论坛里有人提到要支持 ESP32C3。我在想,这C3不是没MCPWM么? SimpleFOC咋支持? 事实是,SimpleFOC 也确实不支持 C3。但是有人回复他实现过。就用的 LEDC PWM。 要知道,ESP32C3 可比 S3 便宜了一半还多。要真的能驱动电机,那我的 VVVF 变频器大业,又多了一项可选的MCU! 实践 虽然别人有提过他用 LEDC PWM 实现了 foc。但是吧,无代码无真相。但是总归人家说可以。那我研究研究吧。于是购入 ESP32S3。 等等,不是说C3吗?咋买了S3呢?因为我确信我的VVVF需要蓝牙!需要WIFI!AT32F415已经不能满足我的需求了。 然后顺便买了个9.9的 ESP32C3开发板。 等开发板到了,我马上研究起了 ESP32C3。虽然C3是顺便买的,但是不妨碍我先研究它。 于是在项目里创建了 lib/libvfd/hal/esp32c3pwm.{hpp,cpp} 文件。 着手研究 ESP32C3 里的 LEDC PWM。 最后踩了无数的坑后,把他实现出来了。 #if defined(ESP_PLATFORM) #ifdef CONFIG_IDF_TARGET_ESP32C3 #include "esp32c3pwm.hpp" #include "driver/ledc.h" #include "esp_err.h" #include "esp_timer.h" #include "freertos/FreeRTOS.h" #include "freertos/task.h" #include "freertos/timers.h" #include "private/commons.hpp" #include "os/os.hpp" #define FOC_MCPWM_TIMER_RESOLUTION_HZ 40000000 // 40MHz, 1 tick = 0.025us #ifndef INVERT_LOW_SIDE #define INVERT_LOW_SIDE 0 #endif const static char* TAG = "vfd"; namespace motorlib { struct esp32c3pwmdriver_impl { /* * Prepare and set configuration of timers * that will be used by LED Controller */ ledc_timer_config_t timer_config = { .speed_mode = LEDC_LOW_SPEED_MODE, // timer mode .duty_resolution = LEDC_TIMER_13_BIT, // resolution of PWM duty .timer_num = LEDC_TIMER_0, // timer index .freq_hz = 4000, // frequency of PWM signal .clk_cfg = LEDC_AUTO_CLK, // Auto select the source clock }; int gen_gpios[6]; // 3 GPIO pins for generator config // hardware variables int pwm_frequency; int pwm_period; esp32c3pwmdriver_impl( int pin_AH, int pin_AL, int pin_BH, int pin_BL, int pin_CH, int pin_CL, int PWM_freq) : pwm_frequency(PWM_freq) { gen_gpios[0] = pin_AH; gen_gpios[1] = pin_BH; gen_gpios[2] = pin_CH; gen_gpios[3] = pin_AL; gen_gpios[4] = pin_BL; gen_gpios[5] = pin_CL; // ledc_timer_config.duty_resolution = ledc_find_suitable_duty_resolution(LEDC_USE_XTAL_CLK, pwm_frequency); pwm_period = 1 << timer_config.duty_resolution; // pwm_frequency = timer_config.freq_hz; esp_err_t ret; ledc_timer_rst(LEDC_LOW_SPEED_MODE, LEDC_TIMER_0); ret = ledc_timer_config(&timer_config); timer_config.timer_num = LEDC_TIMER_1; ret = ledc_timer_config(&timer_config); os::printf("ledc_channel_config return %d\n", ret); ledc_channel_config_t ledc_channel[] = { { .gpio_num = pin_AH, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_0, .timer_sel = LEDC_TIMER_0, .duty = 1, .hpoint = 0, .flags = { .output_invert = 0 }, }, { .gpio_num = pin_BH, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_1, .timer_sel = LEDC_TIMER_0, .duty = 1, .hpoint = 0, .flags = { .output_invert = 0 }, }, { .gpio_num = pin_CH, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_2, .timer_sel = LEDC_TIMER_0, .duty = 1, .hpoint = 0, .flags = { .output_invert = 0 }, }, { .gpio_num = pin_AL, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_3, .timer_sel = LEDC_TIMER_1, .duty = 1, .hpoint = 0, .flags = { .output_invert = !INVERT_LOW_SIDE } }, { .gpio_num = pin_BL, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_4, .timer_sel = LEDC_TIMER_1, .duty = 1, .hpoint = 0, .flags = { .output_invert = !INVERT_LOW_SIDE } }, { .gpio_num = pin_CL, .speed_mode = LEDC_LOW_SPEED_MODE, .channel = LEDC_CHANNEL_5, .timer_sel = LEDC_TIMER_1, .duty = 1, .hpoint = 0, .flags = { .output_invert = !INVERT_LOW_SIDE } }, }; for (int ch = 0; ch < 6; ch++) { ret = ledc_channel_config(&ledc_channel[ch]); os::printf("ledc_channel_config return %d\n", ret); } stop(); } void set_duty(float_number U_a, float_number U_b, float_number U_c) { auto u_lpoint = clamp<int>(U_a * pwm_period, 0, pwm_period-1); auto v_lpoint = clamp<int>(U_b * pwm_period, 0, pwm_period-1); auto w_lpoint = clamp<int>(U_c * pwm_period, 0, pwm_period-1); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_0, u_duty); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_1, v_duty); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_2, w_duty); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_3, u_duty); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_4, v_duty); ledc_set_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_5, w_duty); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_0); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_1); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_2); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_3); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_4); ledc_update_duty(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_5); } void set_frequency(int freq) { if (freq <= 6000 && freq >= 3000) { ledc_set_freq(LEDC_LOW_SPEED_MODE, LEDC_TIMER_0, freq); ledc_set_freq(LEDC_LOW_SPEED_MODE, LEDC_TIMER_1, freq); pwm_frequency = freq; esp_timer_restart(hr_timer, 1000000/freq); } } void stop() { ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_0, 0); ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_1, 0); ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_2, 0); ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_3, 0); ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_4, 0); ledc_stop(LEDC_LOW_SPEED_MODE, LEDC_CHANNEL_5, 0); } void start() { } int get_frequency() { return pwm_frequency; } pwmdriver::timer_fn pwm_cb; static void timer_cb(void* user_data) { auto _this = reinterpret_cast<esp32c3pwmdriver_impl*>(user_data);_this->pwm_cb(_this->pwm_frequency); } esp_timer_handle_t hr_timer; void link_timer(pwmdriver::timer_fn fn) { pwm_cb = fn; esp_timer_create_args_t timer_arg = { .callback = timer_cb, .arg = this, .dispatch_method = ESP_TIMER_TASK, .name = "pwm_tmr", .skip_unhandled_events = true, }; esp_timer_create(&timer_arg, &hr_timer); // 200us = 5khz pwm esp_timer_start_periodic(hr_timer, 200); } ~esp32c3pwmdriver_impl() { esp_timer_stop(hr_timer); esp_timer_delete(hr_timer); } }; ////////////////////////////////////////////////////////////////////////////// esp32c3pwmdriver::esp32c3pwmdriver( int pin_AH, int pin_AL, int pin_BH, int pin_BL, int pin_CH, int pin_CL) { impl = new esp32c3pwmdriver_impl(pin_AH, pin_AL, pin_BH, pin_BL, pin_CH, pin_CL, 4000); } esp32c3pwmdriver::~esp32c3pwmdriver() { delete impl; } // Function setting the duty cycle to the pwm pin (ex. analogWrite()) // - BLDC driver - 6PWM setting // - hardware specific void esp32c3pwmdriver::set_duty(float_number U_a, float_number U_b, float_number U_c) { impl->set_duty(U_a, U_b, U_c); } void esp32c3pwmdriver::start() { impl->start(); } void esp32c3pwmdriver::stop() { impl->stop(); } int esp32c3pwmdriver::get_frequency() { return impl->get_frequency(); } void esp32c3pwmdriver::set_frequency(int f) { impl->set_frequency(f); } void esp32c3pwmdriver::link_timer(timer_fn fn) { impl->link_timer(fn); } } #endif // CONFIG_IDF_TARGET_ESP32C3 #endif // defined(ESP_PLATFORM) 不同于其他平台使用 PWM 自身的定时器中断,esp32c3 上,pwm 周期更新的回调是由一个高精度定时器回调提供的。之所以不用 pwm 的回调,是因为 ledc pwm 并不会产生这样的中断——除非使用了硬件fade功能。 但电机控制岂是fade能瞎fade的? ...

December 20, 2023